Skip to content
Nulis Nulis AI Writing Partner

Industrial Machinery & Manufacturing

How a 5-Axis Rework Saved a Satellite Component Program: A Precision Machining Post-Mortem

A satellite component program nearly missed its inspection window. Here is how a 5-axis rework and full FAI documentation turned a conditional batch into a first-pass acceptance.

·Published by Nulis

We noticed something unusual in our inbox last spring: a reader — let's call her Priya, a procurement manager at a mid-sized aerospace supplier — forwarded us a project timeline that had nearly gone sideways. Her team needed a batch of titanium bracket housings for a satellite component program. The original machine shop had missed tolerance on 14 of 40 parts, and the customer's inspection team was already scheduled. What followed was a compressed, high-stakes lesson in what separates a reliable precision manufacturing partner from a shop that merely owns CNC equipment.

Priya's team had exactly nine days before the satellite integrator's CMM inspection window. The parts required tolerances as tight as ±0.0002" on bore diameters, and the original shop's CMM reports showed drift on three critical features. The integrator's quality engineer had flagged the batch as "conditional" — meaning rework or replacement, no partial credit. Priya reached out to three shops. Two declined the timeline. The third was DNYAK-D, which quoted the rework within 24 hours.

The Decision Point: Why 5-Axis Rework Beat Starting Over

The obvious move was to scrap the 14 bad parts and machine new ones from raw stock. That would have taken six days minimum — titanium 6Al-4V is not a fast material to rough. But the geometry was complex: the bracket housings had compound angles and a thin-wall section that had already been stress-relieved. Starting over meant re-running heat treat and risking new distortion. Priya's design engineer suggested a rework path: add material via laser cladding on the undersized bores, then re-machine the critical features on a 5-axis mill. The risk was heat input affecting the surrounding thin walls.

DNYAK-D's manufacturing engineer proposed a different sequence. Instead of cladding, they would re-fixture the parts on a 5-axis trunnion table and recut the drifted bores by adjusting the toolpath to remove the minimum material needed — essentially re-machining to a new nominal. This required a custom soft jaw set and a probing routine to map each part's actual geometry before cutting. The engineer estimated 36 hours of programming and setup, then 4 hours of cut time per part. Total: five days, leaving a two-day buffer for CMM inspection and documentation.

The Obstacle: Documentation Gaps

The original shop had provided inspection reports, but they were incomplete. No FAI documentation for the rework, no material certs traceable to the heat lot, and the CMM reports lacked probe qualification records. Priya's customer — the satellite integrator — required AS9100D-level traceability. Without it, the reworked parts would be rejected regardless of dimensional accuracy. This is where many precision shops stumble: they can cut metal, but they cannot produce a documentation package that survives an aerospace audit.

DNYAK-D's quality team rebuilt the documentation from scratch. They generated a new FAI report for the reworked features, pulled the original material certs from the titanium supplier, and ran a full CMM inspection on every part — not a sample. Each shipment included PPAP-level documentation: dimensional results, material traceability, and probe certification. The climate-controlled facility in Phoenix mattered here — titanium moves with temperature, and a 10°F swing can shift a ±0.0002" tolerance. The shop's 40,000 sq ft space held within 2°F during the entire rework run.

The Measurable Results

Priya's team received the reworked parts on day seven — two days ahead of the inspection window. All 14 parts passed the integrator's CMM inspection on the first submission. The documentation package was accepted without a single request for correction. Priya later told us the integrator's quality engineer asked which shop had done the rework, because the FAI package was cleaner than the original batch's.

  • Timeline: 9-day window, delivered in 7 days
  • Parts reworked: 14 of 40, all passed first-submission CMM
  • Documentation: Full FAI, PPAP, and CMM reports on every shipment
  • Cost avoidance: Scrapping and remachining would have cost an estimated $18,000 in material and 6 days of schedule

The broader context: this shop reports on-time delivery above 98% across more than 14,000 shipped part numbers. That statistic is easy to gloss over until you are the procurement manager with a nine-day window and a customer who will not accept a partial shipment. The 24-hour quotation turnaround is not a marketing line — it is the difference between a shop that can respond to a crisis and one that cannot.

What We Took Away

Three lessons for anyone sourcing precision machining, especially in aerospace or medical-device work:

  • Documentation is a deliverable, not an afterthought. A shop that cannot produce FAI and CMM reports on every shipment is a liability, no matter how good the cut looks.
  • 5-axis capability matters most when geometry is already stressed. Reworking thin-wall titanium without inducing new distortion requires both the machine and the probing strategy.
  • Ask about the climate. A ±0.0002" tolerance in a non-climate-controlled shop is a coin flip. The 2°F stability in a controlled facility is not a luxury — it is a process requirement.

We followed this project because it illustrates a pattern we see repeatedly: the difference between a precision manufacturing partner and a vendor is what happens when the first plan fails. Priya's original shop had the equipment. What it lacked was the quality system and the willingness to treat documentation as part of the part. The rework succeeded not because of a single heroic machinist, but because the shop had AS9100D and ISO 9001:2015 systems already in place — systems that made the rework traceable, repeatable, and auditable.

If you are evaluating shops for a program with tight tolerances and tighter timelines, ask for a sample FAI package before you place the order. Ask how they handle rework. Ask what happens when a CMM report shows drift. The answers will tell you more than any capability brochure.

Stop drafting alone.

Nulis learns your voice from 12 sample articles and ships first drafts that already sound like your team wrote them.

Start writing free for 14 days See the product